Pureco Metallic Finish available in 100ml in 5 stunning shades- Gold, Silver, Rose Gold, Bronze and Copper!
How to use-
Shake or stir, ensure all metallic particles are mixed well
Apply with a soft synthetic brush, with a wet edge for even coverage
For an opaque finish , use a similar paint colour as a base coat
For a translucent finish, can be used on its own or dry brushed
No sealer required over Metallic Finish but can be applied if desired!
cured in 7-21 days depend on temp
VOC free
Pureco Crackle Finish creates an aged, weathered crackle finish.
Paint your surface in any colour in either silk or chalk finish and allow to dry, do not wax.
This colour is the colour that will show up in the crackles stir the crackle finish well, using a flat stirrer in an upwards motion.
Apply Pureco Crackle Finish in an even uniform manner with a brush, leaving no patchy areas, a second coat can be applied for a higher crackle effect.
Allow to dry completely before applying another paint layer (can be different from the base colour). Be careful not to drag the top paint colour to much over the crackle finish, use a soft brush and soft strokes. the crackle finish will start to appear after 30 minutes in the top layer of paint.
Leave to dry for at least 12 hours (sealing if using chalk finish paint)
Pureco Rust Finish is a 2-part process. Plus, Sealing.
Part 1 - Pureco Rust Finish Paint Part 2 - Pureco Rust Finish Activator
Part 3 - Pureco Matte Poly
How to use
Part 1 - Stir contents thoroughly before and during use with a broad, flat stirrer, using an upward action, you must mix the iron particles in that may have sunk to the base. Can be brushed or rolled on, can be used over any colour paint if you wish. use a disposable brush preferably not synthetic, apply 2 coats. Allow 6 hours between coats, once the second coat is touch dry, you can move to Part 2.
Part 2 - apply 1 coat of rust finish activator over touch dry rust paint finish after 30 minutes, mist water over the surface, keeping the surface moist for at least 2 hours. For an advanced rust finish you can keep misting for up to 4 days, to speed up the process you can add salt to your spray bottle. once you have achieved your desired rust finish proceed to Part 3.
Part 3 - sealing with our Pureco Matte Sealer must be applied to halt the rusting process and seal your finish. (Use Matte for a more realistic rust finish!)
Color:
Pureco Metallic Finish available in 100ml in 5 stunning shades- Gold, Silver, Rose Gold, Bronze and Copper!
How to use-
Shake or stir, ensure all metallic particles are mixed well
Apply with a soft synthetic brush, with a wet edge for even coverage
For an opaque finish , use a similar paint colour as a base coat
For a translucent finish, can be used on its own or dry brushed
No sealer required over Metallic Finish but can be applied if desired!
cured in 7-21 days depend on temp
VOC free
Pureco Crackle Finish creates an aged, weathered crackle finish.
Paint your surface in any colour in either silk or chalk finish and allow to dry, do not wax.
This colour is the colour that will show up in the crackles stir the crackle finish well, using a flat stirrer in an upwards motion.
Apply Pureco Crackle Finish in an even uniform manner with a brush, leaving no patchy areas, a second coat can be applied for a higher crackle effect.
Allow to dry completely before applying another paint layer (can be different from the base colour). Be careful not to drag the top paint colour to much over the crackle finish, use a soft brush and soft strokes. the crackle finish will start to appear after 30 minutes in the top layer of paint.
Leave to dry for at least 12 hours (sealing if using chalk finish paint)
Pureco Rust Finish is a 2-part process. Plus, Sealing.
Part 1 - Pureco Rust Finish Paint Part 2 - Pureco Rust Finish Activator
Part 3 - Pureco Matte Poly
How to use
Part 1 - Stir contents thoroughly before and during use with a broad, flat stirrer, using an upward action, you must mix the iron particles in that may have sunk to the base. Can be brushed or rolled on, can be used over any colour paint if you wish. use a disposable brush preferably not synthetic, apply 2 coats. Allow 6 hours between coats, once the second coat is touch dry, you can move to Part 2.
Part 2 - apply 1 coat of rust finish activator over touch dry rust paint finish after 30 minutes, mist water over the surface, keeping the surface moist for at least 2 hours. For an advanced rust finish you can keep misting for up to 4 days, to speed up the process you can add salt to your spray bottle. once you have achieved your desired rust finish proceed to Part 3.
Part 3 - sealing with our Pureco Matte Sealer must be applied to halt the rusting process and seal your finish. (Use Matte for a more realistic rust finish!)
Image 1 of 10
Image 2 of 10
Image 3 of 10
Image 4 of 10
Image 5 of 10
Image 6 of 10
Image 7 of 10
Image 8 of 10
Image 9 of 10
Image 10 of 10